1/35 "Ingram 2" Patlabor - Part 4

Now to work on the Ingram’s arms.

The top joints are both the same & as they will not be seen on the finished kit I just screwed them together as in section 11 of the manual.   The right hand side lower arm is meant to slide down so he can reach the gun mounted in the leg & does need a bit of work.

The sides of the arm & rear plate E6 were painted Plate Mail primer, the sliding beam & fixing clip in Magnesium & the piston in Plate Mail & a copper top section. The left arm comes in just 2 pieces & was done in Plate Mail & copper. The outer armour pieces (B30,B31,B32 & B33) were sprayed in the White primer.

 You need to cut 2 pieces of red wire that go through the arm & bend into place.  The completed lower arm sits into the armour.

The end caps (A16) were sprayed in Satin Black then they push into place on the arm.

The hip joint is a simple 3 piece unit that screws together, the connecting joint D13 pushed into place, then sprayed in Plate Mail primer.

 The outer casing for the hips (B38) had the winch fitted & then sprayed in White primer.  The winch cable was hand painted in Aluminium & then a black wash to bring out the depth of the cable more.

This unit then pushes into the waist section that was done back on part 2 of this blog.

1/35 "Ingram 2" Patlabor - Part 3

 Time to do some work on the cockpit area even though a lot of it will never be seen again J.

The seat comes in 3 parts with the rear bulkhead details moulded on the main part.  I used Vallejo Grey primer for a base coat.

The rest of the seat & bulkhead were highlighted in Vallejo U.S.Grey (71.047), Fire Red ( 71.084), Black (71.057) & Plate Mail primer.

The side walls of the cockpit were sprayed with Grey primer, then 3 coats of Exhaust Manifold. To try & represent the display screens I used  “Ammo Of Mig” Crystal Green (A.MIG-092), but in the pictures it just doesn’t show the deep colour it gave.

The cockpit was screwed together as in section 24, where the poly caps & some small parts were fitted.  Please pay attention on how to fit parts D10 & D9 as they need to go in before you screw it together.

They need to go on the inside of the cockpit horizontally to click in place then gently rotate them so they sit upright.  The side pods of the body (D21 & D22) were sprayed the same way as the cockpit & the arms (D16,D17,F1 & F2) in Plate Mail primer. These parts then fit onto what now has become the body of the Ingram.

 The completed flip down screen (F9 & F10) were primed, then painted in U.S.Grey. This time I brushed some Aluminium (71.062) first into where the screen should be & when dry used the Crystal Green. As you can see this gave a much better result.    

The final part for now on the body was to lower body panel B37, which has been sprayed with the White primer & the grey rubber boot that should have gone on the waist.  The reason I fitted it here was there are 2 pegs it has to sit on at the front of the body & I could see it was easier to get these fitted first then place the lower body panel over the boot to lock it in position.

I am still not happy with how these rubber parts look even with the seam lines taken out & I wish there was a way to totally remove the mould lines & not ruin the detail.

1/35 "Ingram 2" Patlabor - Part 2

The upper part of the legs will barely be seen, but that doesn’t stop me from painted them once built. Once the units were put together as in section 4 of the instructions they were sprayed in Vallejo Plate Mail primer (VAL 70.628) & allowed to dry.

Time to spray all outer leg armour parts & all of them were given a light sanding to remove any nub marks where they were taken off the sprue, but it also helps as washing them after also removes any mould release agent that can affect the paint going onto the plastic.

As mentioned at the start these were painted in a few light coats of Vallejo white primer (VAL 600) with light sand between coats when it was fully dry. Please make sure it is dry before you start to sand the primer.

It was at this stage I decided to do some detail work on the lower legs & my using a small amount of the following paints gave them a bit of a lift. I used Vallejo “Metal Color” Magnesium ( 77.711), Exhaust Manifold ( 77.723) & some “Ammo Of Mig” Old Brass (A.MIG-190)

The outer parts easily clipped into place & I left the legs on one side till later.

 Looking at the lights in the waist they are meant to be orange, but in the kit they are clear.  I have some “Ammo Of Mig” Crystal Orange (A.MIG-097) that will do the job nicely with 3 light coats.

The waist parts were sprayed in white & black primer then went together as in section 8, but I left off the rubber gaiter till a later stage.

Slight accident here as I dropped an open permanent paint marker on the waist unit while doing another model so had to re-spray the top after masking the rest off.

1/35 "Ingram 2" Patlabor - Part 1

Moved away from armour kits for a while & going back to one of my 1^st loves Sci-Fi, or in this case more correctly Gundam & Anime.

This kit is called “AV-98 Ingram 2” & is meant to be a 1:35 scale model of the armoured unit used by Tokyo police in the TV series.  These are meant to be just a snap fix kit with no painting, but I always paint & try to remove as many seam lines as possible, so here is how I built mine.

For all the white parts I am going to use my stock Vallejo white primer (VAL 600) as it goes on well, has a slight satin sheen when sprayed in very light coats & will not hide any of the kits detail.

To make both feet I put the “poly cap” (PC J) into part F14 & glued this & F15 together.  The seam lines were sanded down & the unit sprayed in Vallejo Plate Mail primer (VAL 70.628).

The sole of the foot (A3) & the base (A1) were glued together & allowed to dry.  The completed base & heel (A11) were sanded and sprayed Satin Black & allowed to dry.  The tops of the foot (I6) & (I1) were painted white then all the parts just press into the foot support.

The right hand leg has an opening side where a pistol sits & a mechanism pulls the gun out when the outer armour is moved.  The inner working (E9,16,17,23,24,25 & 30) were sprayed in Plate Mail  primer. 

As the leg interior may be on show it will be painted & have some details added. The whole leg parts were primed with grey primer (VAL 601). The insides of part (D8 & D20) were given several light coats of Exhaust Manifold ( 77.723) from the Vallejo “Metal Color” range were applied to the inside. When dry the inner was masked & the outer sectioned sprayed with “Metal Color” Aluminium ( 77.701). This gives just a slight colour change when you put the final leg together.

The inner working just push fitted together but pay attention to the manual as to how to fit part E30 as this need to move a certain way. 

The left leg has no moving parts, but to keep the same colour scheme the parts D7 & D19 were primed & the inner & outer parts sprayed the same Exhaust Manifold & Aluminium colours.  The small fixing pieces for the legs (D14,D15,E18 & E19) were sprayed with Plate Mail  primer.

1:12 Porsche 910 :- 15- Final assembly & decals

Homeward stretch now & the Porsche is nearly finished.

Time to do the final bits to the upper body.  The front section under the bonnet needs completed oil cooler fitted. The instructions show no pipe work going to it, so I drilled 2 small holes where the hoses should, in my view, come out & in the back of the cooler & by using a bit of scrap tubing made some pipes

The rear section of the body had the surrounds & lights fitted using clear glue as not to affect the red lens.

Now the oil cooler has set in place I masked off the inside of the front lights so I could spray them with Vallejo Black primer as it gives a nice satin effect.  Getting normal masking tape to go round small corners has been a problem for me until now.  I found some flexible masking tape that is only 2mm wide & more importantly stays in place. A couple of light coats are all it required.

The 4 headlights fronts have a small notch at the bottom, so please take note when gluing them in place as they will not sit correctly if not.

Using clear glue I fitted the lights & indicators then the top clear cover was fitted with a small amount of glue.

Honesty time here I made a right mess of the masks in the kit for the black surrounds to the windscreen in section 21, so had to mask it using the flexible tape & then spray it. The completed screen & dashboard were glued in place.

The reaming small parts for the front including the wipers were painted & put in position. 

When it came to the decal part I decided to use just a few of them as the kit was not an accurate representation of an actual car, but one that had been brought but still raced in classic races.  With the paint being a gloss the decals stuck to the surface very well & did not need any kind of extra softener or fixing agent.

 

The final stage was just to give the engine bay a slight touch of weathering to show the car was in use, but looked after.

There you have it & again my apologies in the time it took to do this blog & can guarantee the next one will not take as long.

1:12 Tamiya Porsche 910 :- 14- Body & interior work

As I am nearing completion of the Porsche though it time to do some preparation work on the top of the car.

I had a look at the way the roof section (part J12) fitted onto the rear section to see the gap was too large for my personal choice.  The best thing for me was to glue this in position then just give it a light sand so that the join was still visible but was secure.  I then fitted the rear engine cover (J7) under the air intakes.  I masked off the top of the body & sprayed the whole inside with the same Matt Tank grey (Humbrol 67) as the floorpan.

After a few days to make sure the paint was fully cured I masked off the inside areas & gave the whole upper body light coats of the blue used on the underside & giving it a very light sand between coats to remove any imperfections. After about 5 light coats I got the desired paint finish I was looking for.

To let the car paint totally cure & harden, which can take days under normal temperatures, I did some work on the pedals by giving them a light sanding  down to remove some flash marks. The pedals were painted black & the shafts in aluminium.

The wheels I did in blog post No.11 were fitted with the wheel nuts left in the chrome to just give them a slight accent.

Now comes a part that even now I still don’t like… fitting large clear parts into models.  Somehow I cannot get the great finish & unblemished  ones seen in models done by my peers, so have to do my own work around. As this part should not be touched when I’ve finished the kit I used some canopy PVA glue in a small bead around the bulkhead, then held the clear plastic in place with soft ended pegs while it set.

This did set the plastic in place, but I can still some small sections where it looks like the glue hasn’t stuck it down fully.  Tips please required on how to get a better job done of clear parts J.

1:12 Tamiya Porsche 910 :- 13- Seatbelts & bulkhead work

Time to do some more sub-assembly work & make the seatbelts in section 12 & 13.  

First job was to make the locking buckle that comes in 5 parts of small photo-etched metal.  I used a very fine set of sprue cutters to take the parts of the photo-etch frame & a light filing down where the remaining nub of metal still stood.  I found that the very thin superglue is the best for these kinds of parts & just built them up in order in the diagram.

The seatbelt straps are the usual kind Tamiya have with a plain sticky side & a fabric effect on the other.  Take your time & care when making the belts up as the straps are of different sizes & need to be folded in a particular way to look right. They will lose adhesion if you have to keep taking them apart & re-fixing them, so best to read the fitting guides well for each strap before you start.

I do find that even when carefully taken off the backing there are sometimes fine loose strands that need just a trim on the edges after making the belts.

Both seats were sprayed with Satin Black primer then, when dry, the belts were folded over & a small amount of superglue on the back of the seat holds them in place. The completed seats were left on one side for later fitting.

 Still some final bits of work are needed on the rear bulkhead/engine area as in section 11 & 14 where I need to fit the battery & circuit breakers from way back in blog post No.10.  I fitted the battery & circuit breakers to the bulkhead, then fitted the 2 painted cylinders (C28) & the vinyl tubing that bends to fit behind the bulkhead.

The 2 tanks & the large rubber tubing in section 14 then fitted in behind the already pre-fitted bulkhead.